Randall Recto Module

These were Randall's first attempt at a Mesa Boogie Rectifier module.  There have been a number of variants since the original Recto module, each called something different:

  • Recto;
  • Rectified;
  • Treadplate; and
  • Grail (George Lynch signature module version).

SacredGroove in this thread gives some specific information on the component differences:

    This is what I've noticed:
    Recto--C3/.0047uf, C14/470pf, R1-3/470ohm
    Rectified--C3/.0022, C14/470pf, R1-3/470ohm
    Treadplate--C3/.0022, C14/300pf, R1-3/150ohm
    A lot of people change C3 to .001 or .0015 for tighter bass attack.
    Also:
    Grail--C3/.0005uf, C14/470pf, R1-3/150ohm

OKStrat had this to say about the effect of these component mods:

  • Changing R1-R3 to a lower value cuts gain a little bit. Dropping the value of C3 tightens up the low end but too much can affect your 'thump' also. It lowers the gain slightly on the low end, which helps keep the module from sounding too tubby/flubby.

"Original" Recto module

I've got what must be a fairly early example of the original Recto module.  It has the chrome plain face plate and an "Eden Electronics, Proudly made in the USA" sticker on the bottom.  The Key tone shaping component values are as follows:

C3/.001uf, C14/470pf, R1-3/150Ohm

The module does not look like it has had any of these values changed.

Component summary table

ComponentRectoRectifiedTreadplateGrailMy "Recto"
C30.0047uF
0.0022uF0.0022uF0.0005uF0.0022uF
C14470pF
470pF300pF470pF470pF
R1-3470Ohm
470Ohm150Ohm150Ohm150Ohm

Cathode resistors

  • V1 - R16 - 1.8MOhm
  • V2 - R29 - 1.8MOhm

For info on cathode resistors see www.aikenamps.com/index.php/designing-common-cathode-triode-amplifiers.

Recto mods

C3 cap

Originally 0.0022uF, I've tried 0.0015uF and 0.001uF and prefer the 0.001uF the best.

C14 cap

I've also tried various values in the C14 position.  470pF sounds good, 300pF sounds better, 250pF results in a noticeable drop in gain which is not great.

Tubes

The Recto module really likes the Chinese (Shuguang) 12AX7's.  The gain and bite from these tubes is exactly what's needed to bring these modules alive.  

More like the real thing

The defining characteristic of the Mesa Boogie Rectifier preamp is the V2B gain stage which is extremely cold biased by a 39kOhm cathode resistor (resulting in very asymmetrical clipping).  Also, in later models a 220 to 800pF of high pass cap around the plate resistor (to bleed off some of the highs) and a 470pF cap to bypass high to mids around the interstage attenuator resistor were added.

If you take a look at the Randall Recto etc modules, its pretty clear that there are some components you can change to make the circuit closer to that of a real recto.  See the pic below for the components I changed out on mine.  I'm pretty happy with the results. Components with values in bold were changed to the values in bold.  Cap CN1 was also added across R21.


V1A related components mods for Recto/Rectified/Treadplate/Grail modules

Note: Mesa Boogie amps are renowned for having their tone circuits after the first gain stage.  The Randall MTS modules do not copy this aspect of the Boogie amps.  The Randall MTS tone stack is in the usual Marshall/Fender position at the end of gain stages.  As a result, values that affect frequency (like C8, CN1 and C11) may have produce different end results, so often directly copying a portion of another amps preamp circuit will not necessarily produce the same sounding results.

Warpedmusician has come up with some interesting ideas on changing the values of the cathode resistor in the Rectifier's cold clipping stage - warpedmusician.wordpress.com/2016/01/17/dual-rectifier-cold-clipping-mods/#more-3197.

Related articles:

Randall MTS Ultra Module

Issues

Randall MTS Treadplate module

This is basically a later version of the Recto module with a few component changes.  Here's a summary of value differences.

Randall MTS Top Boost module

This module is Randall's take on a boosted Vox AC30TB.

Randall MTS Brahma module

Randall described the module as follows:

Randall MTS Modern module

Apparently the Modern is higher gain version of the Top Boost module.

Randall RM20B

Tube config

Content-type: text/html Error
Sorry, the application you are using has encountered an error.

Please click on this link to report the error: REPORT ERROR